0.2.kubeadm搭建kubernetes高可用集群
目录
kubeadmin安装Kubernetes
kubeadm是官方社区推出的一个用于快速部署kubernetes集群的工具；使用staticPod(容器)运行的管理组件,镜像使用gcr.io域名仓库里的。
0.部署环境&需求
部署版本 kubernetes1.16
| IP | Hostname | 内核 | CPU&Memory | 系统版本 | 备注 |
|---|---|---|---|---|---|
| 192.168.121.81 | k8s-master01 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | control plane |
| 192.168.121.82 | k8s-master02 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | control plane |
| 192.168.121.83 | k8s-master03 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | control plane |
| 192.168.121.84 | k8s-node01 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | worker nodes |
| 192.168.121.85 | k8s-node02 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | worker nodes |
| 192.168.121.86 | k8s-node03 | 4.4.206-1.el7.elrepo.x86_64 | 4C&8M | 7.6.1810 | worker nodes |
| 192.168.121.88 | keepalived | v1.3.5 | vip |
在开始之前，部署Kubernetes集群机器需要满足以下几个条件：
- 一台或多台机器，操作系统 CentOS7.x-86_x64
- 硬件配置：2GB或更多RAM，2个CPU或更多CPU，硬盘30GB或更多
- 集群中所有机器之间网络互通
- 可以访问外网，需要拉取镜像
- 禁止swap分区
1.系统初始化
1.1.主机名
设置永久主机名称，然后重新登录:
]# hostnamectl set-hostname k8s-master01 # 将 k8s-master01 替换为当前主机名
- 设置的主机名保存在
/etc/hostname文件中；
如果 DNS 不支持解析主机名称，则需要修改每台机器的 /etc/hosts 文件，添加主机名和 IP 的对应关系：
]# cat >> /etc/hosts <<EOF 192.168.121.81 k8s-master01 192.168.121.82 k8s-master02 192.168.121.83 k8s-master03 192.168.121.84 k8s-node01 192.168.121.85 k8s-node02 192.168.121.86 k8s-node03 EOF
1.2.添加 docker 账户
在每台机器上添加 docker 账户：
]# useradd -m docker
1.3.无密码 ssh 登录其它节点
如果没有特殊指明，本文档的所有操作均在 k8s-master01 节点上执行，然后远程分发文件和执行命令，所以需要添加该节点到其它节点的 ssh 信任关系。
设置 k8s-master 的 root 账户可以无密码登录所有节点：
]# ssh-keygen -t rsa ]# ssh-copy-id ]# ssh-copy-id ]# ssh-copy-id
1.4.更新 PATH 变量
将可执行文件目录添加到 PATH 环境变量中：
]# echo ‘PATH=/opt/k8s/bin:$PATH‘ >>/root/.bashrc ]# source /root/.bashrc
1.5.安装依赖包
在每台机器上安装依赖包：
]# yum install -y epel-release ]# yum install -y conntrack ntpdate ntp ipvsadm ipset jq iptables curl sysstat libseccomp wget
1.6.关闭防火墙
在每台机器上关闭防火墙，清理防火墙规则，设置默认转发策略：
]# systemctl stop firewalld ]# systemctl disable firewalld ]# iptables -F && iptables -X && iptables -F -t nat && iptables -X -t nat ]# iptables -P FORWARD ACCEPT
1.7.关闭 swap 分区
如果开启了 swap 分区，kubelet 会启动失败(可以通过将参数 --fail-swap-on 设置为 false 来忽略 swap on)，故需要在每台机器上关闭 swap 分区。同时注释 /etc/fstab 中相应的条目，防止开机自动挂载 swap 分区：
]# swapoff -a ]# sed -i ‘/ swap / s/^\(.*\)$/#\1/g‘ /etc/fstab
1.8.关闭 SELinux
关闭 SELinux，否则后续 K8S 挂载目录时可能报错 Permission denied：
]# setenforce 0 ]# sed -i ‘s/^SELINUX=.*/SELINUX=disabled/‘ /etc/selinux/config
1.9.关闭 dnsmasq（可选）
linux 系统开启了 dnsmasq 后(如 GUI 环境)，将系统 DNS Server 设置为 127.0.0.1，这会导致 docker 容器无法解析域名，需要关闭它：
]# systemctl stop dnsmasq ]# systemctl disable dnsmasq
1.10.加载内核模块
]# modprobe ip_vs_rr ]# modprobe br_netfilter
1.11.优化内核参数
]# cat > kubernetes.conf <<EOF net.bridge.bridge-nf-call-iptables=1 net.bridge.bridge-nf-call-ip6tables=1 net.ipv4.ip_forward=1 net.ipv4.tcp_tw_recycle=0 vm.swappiness=0 # 禁止使用 swap 空间，只有当系统 OOM 时才允许使用它 vm.overcommit_memory=1 # 不检查物理内存是否够用 vm.panic_on_oom=0 # 开启 OOM fs.inotify.max_user_instances=8192 fs.inotify.max_user_watches=1048576 fs.file-max=52706963 fs.nr_open=52706963 net.ipv6.conf.all.disable_ipv6=1 net.netfilter.nf_conntrack_max=2310720 EOF ]# cp kubernetes.conf /etc/sysctl.d/kubernetes.conf ]# sysctl -p /etc/sysctl.d/kubernetes.conf
- 必须关闭 tcp_tw_recycle，否则和 NAT 冲突，会导致服务不通；
- 关闭 IPV6，防止触发 docker BUG；
1.12.设置系统时区
# 调整系统 TimeZone ]# timedatectl set-timezone Asia/Shanghai # 将当前的 UTC 时间写入硬件时钟 ]# timedatectl set-local-rtc 0 ### 重启依赖于系统时间的服务 ]# systemctl restart rsyslog ]# systemctl restart crond
1.13.关闭无关的服务
]# systemctl stop postfix && systemctl disable postfix
1.14.升级内核
CentOS 7.x 系统自带的 3.10.x 内核存在一些 Bugs，导致运行的 Docker、Kubernetes 不稳定，例如：
- 高版本的 docker(1.13 以后) 启用了
3.10 kernel实验支持的kernel memory account功能(无法关闭)，当节点压力大如频繁启动和停止容器时会导致cgroup memory leak； - 网络设备引用计数泄漏，会导致类似于报错：
"kernel:unregister_netdevice: waiting for eth0 to become free. Usage count = 1";
解决方案如下：
- 升级内核到 4.4.X 以上；
- 或者，手动编译内核，
disable CONFIG_MEMCG_KMEM特性； - 或者，安装修复了该问题的
Docker 18.09.1及以上的版本。但由于 kubelet 也会设置 kmem（它 vendor 了 runc），所以需要重新编译 kubelet 并指定GOFLAGS="-tags=nokmem"；
这里采用升级内核的解决办法：
]# rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm # 安装完成后检查 /boot/grub2/grub.cfg 中对应内核 menuentry 中是否包含 initrd16 配置，如果没有，再安装一次！ ]# yum --enablerepo=elrepo-kernel install -y kernel-lt # 设置开机从新内核启动 ]# grub2-set-default 0
安装内核源文件（可选，在升级完内核并重启机器后执行）:
]# yum erase kernel-headers ]# yum --enablerepo=elrepo-kernel install kernel-lt-devel-$(uname -r) kernel-lt-headers-$(uname -r)
1.15.关闭 NUMA
]# cp /etc/default/grub{,.bak}
]# vim /etc/default/grub # 在 GRUB_CMDLINE_LINUX 一行添加 `numa=off` 参数，如下所示：
]# diff /etc/default/grub.bak /etc/default/grub
6c6
< GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=centos/root rhgb quiet"
---
> GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=centos/root rhgb quiet numa=off"重新生成 grub2 配置文件：
]# cp /boot/grub2/grub.cfg{,.bak}
]# grub2-mkconfig -o /boot/grub2/grub.cfg1.16.文件最大数
]# cat>/etc/security/limits.d/kubernetes.conf<<EOF * soft nproc 131072 * hard nproc 131072 * soft nofile 131072 * hard nofile 131072 root soft nproc 131072 root hard nproc 131072 root soft nofile 131072 root hard nofile 131072 EOF
2.开始部署
2.1.部署Docker
每台机器上安装Docker，建议使用18.09版本。
]# wget https://mirrors.aliyun.com/docker-ce/linux/centos/docker-ce.repo -O /etc/yum.repos.d/docker-ce.repo ]# yum list docker-ce --showduplicates | sort -r ]# yum install docker-ce-18.09.9 docker-ce-cli-18.09.9 containerd.io -y
镜像下载加速：
]# curl -sSL https://get.daocloud.io/daotools/set_mirror.sh | sh -s http://f1361db2.m.daocloud.io
设置cgroup驱动，推荐systemd：
]# mkdir -p /etc/docker
]# cat > /etc/docker/daemon.json <<EOF
{
"registry-mirrors": ["https://docker.mirrors.ustc.edu.cn","http://f1361db2.m.daocloud.io"],
"exec-opts": ["native.cgroupdriver=systemd"],
"log-driver": "json-file",
"log-opts": {"max-size": "100m"},
"storage-driver": "overlay2"
}
EOF
]# systemctl enable docker
]# systemctl start docker修改cgroupdriver是为了消除告警：[WARNING IsDockerSystemdCheck]: detected “cgroupfs” as the Docker cgroup driver. The recommended driver is “systemd”. Please follow the guide at https://kubernetes.io/docs/setup/cri/
启动&验证
]# systemctl enable --now docker ]# docker --version Docker version 18.09.9, build 039a7df9ba
2.2.部署keepalived
k8s-master节点都执行本部分操作。
安装keepalived
]# yum -y install keepalived
keepalived配置
master01上keepalived配置：
[ ~]# more /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
router_id master01
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 50
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
192.168.121.88
}
}master02上keepalived配置：
[ ~]# more /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
router_id master02
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 50
priority 90
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
192.168.121.88
}
}master03上keepalived配置：
[ ~]# more /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
router_id master03
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 50
priority 80
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
192.168.121.88
}启动keepalived
所有k8s-mster节点启动keepalived服务并设置开机启动
]# service keepalived start ]# systemctl enable keepalived
VIP查看
]# ip a
确保vip在master01上；否则在初始化安装会无法连接api-server
2.3.部署管理工具kubeadm
在所有节点操作
]# cat <<EOF >/etc/yum.repos.d/kubernetes.repo [kubernetes] name=Kubernetes baseurl=https://mirrors.aliyun.com/kubernetes/yum/repos/kubernetes-el7-x86_64 enabled=1 gpgcheck=0 EOF
maser节点安装
]# yum install -y kubeadm-1.16.4 kubectl-1.16.4 kubelet-1.16.4 ]# systemctl enable kubelet
node节点安装
]# yum install -y kubeadm-1.16.4 kubelet-1.16.4 ]# systemctl enable kubelet
命令补全
安装bash-completion
]# yum -y install bash-completion
加载bash-completion
]# source /etc/profile.d/bash_completion.sh
启动kubelet并设置开机启动
]# systemctl enable kubelet && systemctl start kubelet
kubectl命令补全
]# echo "source <(kubectl completion bash)" >> ~/.bash_profile ]# source .bash_profile
2.4.下载镜像
镜像下载的脚本
Kubernetes几乎所有的安装组件和Docker镜像都放在goolge自己的网站上,直接访问可能会有网络问题，这里的解决办法是从阿里云镜像仓库下载镜像，拉取到本地以后改回默认的镜像tag。本文通过运行image.sh脚本方式拉取镜像。
]# more image.sh
#!/bin/bash
url=registry.aliyuncs.com/google_containers
version=v1.16.4
images=(`kubeadm config images list --kubernetes-version=$version|awk -F ‘/‘ ‘{print $2}‘`)
for imagename in ${images[@]} ; do
docker pull $url/$imagename
docker tag $url/$imagename k8s.gcr.io/$imagename
docker rmi -f $url/$imagename
doneurl为阿里云镜像仓库地址，version为安装的kubernetes版本。
下载镜像
运行脚本image.sh，下载指定版本的镜像
]# chmod +x image.sh ]# ./image.sh ]# docker images
3.初始化Master&Node
master01节点执行本部分操作。
3.1.配置初始化文件
]# more kubeadm_config.yaml
apiVersion: kubeadm.k8s.io/v1beta2
kind: ClusterConfiguration
kubernetesVersion: v1.16.4
certificatesDir: /etc/kubernetes/pki
clusterName: kubernetes
apiServer:
extraArgs:
authorization-mode: "Node,RBAC"
runtime-config: api/all,settings.k8s.io/v1alpha1=true
storage-backend: etcd3
etcd-servers: https://192.168.121.81:2379,https://192.168.121.82:2379,https://192.168.121.83:2379
certSANs: #填写所有kube-apiserver节点的hostname、IP、VIP
- k8s-master01
- k8s-master02
- k8s-master03
- k8s-node01
- k8s-node02
- k8s-node03
- 192.168.121.81
- 192.168.121.82
- 192.168.121.83
- 192.168.121.84
- 192.168.121.85
- 192.168.121.86
- 192.168.121.87
- 192.168.121.88
extraVolumes:
- hostPath: /etc/localtime
mountPath: /etc/localtime
name: localtime
readOnly: true
etcd:
local:
dataDir: /var/lib/etcd
serverCertSANs:
- master
- 192.168.121.81
- 192.168.121.82
- 192.168.121.83
- k8s-master01
- k8s-master02
- k8s-master03
peerCertSANs:
- master
- 192.168.121.81
- 192.168.121.82
- 192.168.121.83
- k8s-master01
- k8s-master02
- k8s-master03
extraArgs:
auto-compaction-retention: "1h"
max-request-bytes: "33554432"
quota-backend-bytes: "8589934592"
enable-v2: "false"
controlPlaneEndpoint: "192.168.121.88:6443"
networking:
podSubnet: "10.244.0.0/16"
---
apiVersion: kubeproxy.config.k8s.io/v1alpha1
kind: KubeProxyConfiguration
mode: ipvs #启动ipvs mode；默认iptables mode
ipvs:
excludeCIDRs: null
minSyncPeriod: 0s
scheduler: "rr"
strictARP: false
syncPeriod: 15s
iptables:
masqueradeAll: true
masqueradeBit: 14
minSyncPeriod: 0s
syncPeriod: 30s
---
apiVersion: kubelet.config.k8s.io/v1beta1
kind: KubeletConfiguration
cgroupDriver: systemd
failSwapOn: truekubeadm_config.yaml为初始化的配置文件
3.2.master初始化
检查文件是否错误，忽略warning，错误的话会抛出error
]# kubeadm init --config /root/initconfig.yaml --dry-run
进行初始化
]# kubeadm init --config=kubeadm_config.yaml ...... Your Kubernetes control-plane has initialized successfully! To start using your cluster, you need to run the following as a regular user: mkdir -p $HOME/.kube sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config sudo chown $(id -u):$(id -g) $HOME/.kube/config You should now deploy a pod network to the cluster. Run "kubectl apply -f [podnetwork].yaml" with one of the options listed at: https://kubernetes.io/docs/concepts/cluster-administration/addons/ You can now join any number of control-plane nodes by copying certificate authorities and service account keys on each node and then running the following as root: kubeadm join 192.168.121.88:6443 --token kkpntz.yc5ow033k2mnp0z4 --discovery-token-ca-cert-hash sha256:bbc3c89aa94f90c457fc6a61f66c39b8bfccb12e84cd8df31ce226e09f0ea839 --control-plane Then you can join any number of worker nodes by running the following on each as root: kubeadm join 192.168.121.88:6443 --token kkpntz.yc5ow033k2mnp0z4 --discovery-token-ca-cert-hash sha256:bbc3c89aa94f90c457fc6a61f66c39b8bfccb12e84cd8df31ce226e09f0ea839
复制kubectl的kubeconfig，kubectl的kubeconfig路径默认是~/.kube/config
]# mkdir -p $HOME/.kube ]# sudo cp /etc/kubernetes/admin.conf $HOME/.kube/config ]# sudo chown $(id -u):$(id -g) $HOME/.kube/config
init的yaml信息实际上会存在集群的configmap里，我们可以随时查看，该yaml在其他node和master join的时候会使用到
kubectl -n kube-system get cm kubeadm-config -o yaml
加载环境变量
]# echo "export KUBECONFIG=/etc/kubernetes/admin.conf" >> ~/.bash_profile ]# source .bash_profile
配置其他master的k8s管理组件
for node in 192.168.33.102 192.168.33.103;do
ssh $node ‘mkdir -p /etc/kubernetes/pki/etcd‘
scp -r /root/kubeadm_config.yaml $node:/root/kubeadm_config.yaml
scp -r /root/image.sh $node:/root/image.sh
scp -r /etc/kubernetes/pki/ca.* $node:/etc/kubernetes/pki/
scp -r /etc/kubernetes/pki/sa.* $node:/etc/kubernetes/pki/
scp -r /etc/kubernetes/pki/front-proxy-ca.* $node:/etc/kubernetes/pki/
scp -r /etc/kubernetes/pki/etcd/ca.* $node:/etc/kubernetes/pki/etcd/
done配置其余k8s-master
]# kubeadm join 192.168.121.88:6443 --token kkpntz.yc5ow033k2mnp0z4 --discovery-token-ca-cert-hash sha256:bbc3c89aa94f90c457fc6a61f66c39b8bfccb12e84cd8df31ce226e09f0ea839 --control-plane
所有master配置kubectl,准备kubectl的kubeconfig
]# mkdir -p $HOME/.kube ]# sudo cp /etc/kubernetes/admin.conf $HOME/.kube/config ]# sudo chown $(id -u):$(id -g) $HOME/.kube/config
设置kubectl的补全脚本
]# kubectl completion bash > /etc/bash_completion.d/kubectl ]# source /etc/bash_completion.d/kubectl
3.3.node初始化
在node节点执行
和master的join一样，提前准备好环境和docker，然后join的时候不需要带--control-plane
]# kubeadm join 192.168.121.88:6443 --token kkpntz.yc5ow033k2mnp0z4 --discovery-token-ca-cert-hash sha256:bbc3c89aa94f90c457fc6a61f66c39b8bfccb12e84cd8df31ce226e09f0ea839
3.4.初始化失败
如果初始化失败，可执行kubeadm reset后重新初始化
]# kubeadm reset ]# rm -rf $HOME/.kube/config
4.配置etcdctl
4.1.复制出容器里的etcdctl
]# docker cp `docker ps -a | awk ‘/k8s_etcd/{print $1}‘`:/usr/local/bin/etcdctl /usr/local/bin/etcdctl
]# cat >/etc/profile.d/etcd.sh<<‘EOF‘
ETCD_CERET_DIR=/etc/kubernetes/pki/etcd/
ETCD_CA_FILE=ca.crt
ETCD_KEY_FILE=healthcheck-client.key
ETCD_CERT_FILE=healthcheck-client.crt
ETCD_EP=https://192.168.121.81:2379,https://192.168.121.82:2379,https://192.168.121.83:2379
alias etcd_v3="ETCDCTL_API=3 etcdctl --cert ${ETCD_CERET_DIR}/${ETCD_CERT_FILE} --key ${ETCD_CERET_DIR}/${ETCD_KEY_FILE} --cacert ${ETCD_CERET_DIR}/${ETCD_CA_FILE} --endpoints $ETCD_EP"
EOF
source /etc/profile.d/etcd.sh
etcd_v3 endpoint status --write-out=table
+-----------------------------+------------------+---------+---------+-----------+-----------+------------+
| ENDPOINT | ID | VERSION | DB SIZE | IS LEADER | RAFT TERM | RAFT INDEX |
+-----------------------------+------------------+---------+---------+-----------+-----------+------------+
| https://192.168.121.81:2379 | d572bef816d9cb7e | 3.3.15 | 3.2 MB | false | 52 | 64002 |
| https://192.168.121.82:2379 | a4b42aafeef9bab3 | 3.3.15 | 3.2 MB | true | 52 | 64002 |
| https://192.168.121.83:2379 | c5d52def73f50ceb | 3.3.15 | 3.2 MB | false | 52 | 64002 |
+-----------------------------+------------------+---------+---------+-----------+-----------+------------+
etcd_v3 endpoint health --write-out=table
+-----------------------------+--------+-------------+-------+
| ENDPOINT | HEALTH | TOOK | ERROR |
+-----------------------------+--------+-------------+-------+
| https://192.168.121.82:2379 | true | 28.336842ms | |
| https://192.168.121.81:2379 | true | 29.132682ms | |
| https://192.168.121.83:2379 | true | 47.635089ms | |
+-----------------------------+--------+-------------+-------+4.2.配置etcd备份脚本
mkdir -p /opt/etcd
cat>/opt/etcd/etcd_cron.sh<<‘EOF‘
#!/bin/bash
set -e
export PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/root/bin
: ${bak_dir:=/root/} #缺省备份目录,可以修改成存在的目录
: ${cert_dir:=/etc/kubernetes/pki/etcd/}
: ${endpoints:=https://192.168.121.81:2379,https://192.168.121.82:2379,https://192.168.121.83:2379}
bak_prefix=‘etcd-‘
cmd_suffix=‘date +%Y-%m-%d-%H:%M‘
bak_suffix=‘.db‘
#将规范化后的命令行参数分配至位置参数（$1,$2,...)
temp=`getopt -n $0 -o c:d: -u -- ""`
[ $? != 0 ] && {
echo ‘
Examples:
# just save once
bash $0 /tmp/etcd.db
# save in contab and keep 5
bash $0 -c 5
‘
exit 1
}
set -- $temp
# -c 备份保留副本数量
# -d 指定备份存放目录
while true;do
case "$1" in
-c)
[ -z "$bak_count" ] && bak_count=$2
printf -v null %d "$bak_count" &>/dev/null || { echo ‘the value of the -c must be number‘;exit 1; }
shift 2
;;
-d)
[ ! -d "$2" ] && mkdir -p $2
bak_dir=$2
shift 2
;;
*)
[[ -z "$1" || "$1" == ‘--‘ ]] && { shift;break; }
echo "Internal error!"
exit 1
;;
esac
done
function etcd_v3(){
ETCDCTL_API=3 etcdctl --cert $cert_dir/healthcheck-client.crt --key $cert_dir/healthcheck-client.key --cacert $cert_dir/ca.crt --endpoints $endpoints
}
etcd::cron::save(){
cd $bak_dir/
etcd_v3 snapshot save $bak_prefix$($cmd_suffix)$bak_suffix
rm_files=`ls -t $bak_prefix*$bak_suffix | tail -n +$[bak_count+1]`
if [ -n "$rm_files" ];then
rm -f $rm_files
fi
}
main(){
[ -n "$bak_count" ] && etcd::cron::save || etcd_v3 snapshot save
}
main
EOFcrontab -e添加下面内容自动保留四个备份副本
]# `crontab -e 0 0 * * * bash /opt/etcd/etcd_cron.sh -c 4 -d /opt/etcd/ &>/dev/null
5.部署插件
5.1.网络查件
5.1.1部署flannel网络
新建flannel网络
]# kubectl apply -f https://raw.githubusercontent.com/coreos/flannel/2140ac876ef134e0ed5af15c65e414cf26827915/Documentation/kube-flannel.yml
由于网络原因，可能会安装失败，建议更换image源，然后再执行apply
5.1.2部署Calico网络(可选)
]# curl https://docs.projectcalico.org/v3.9/manifests/calico-etcd.yaml -o calico.yaml
修改yaml文件、并部署
]# sed -i -e "//" calico.yaml ]# kubectl apply -f calico.yaml
5.2.Web UI（Dashboard搭建）
5.2.1进行配置
下载yaml**
]# swget https://raw.githubusercontent.com/kubernetes/dashboard/v2.0.0-beta8/aio/deploy/recommended.yaml
如果连接超时，可以多试几次
配置yaml
修改镜像地址
]# sed -i ‘s/registry.aliyuncs.com\/google_containers/g‘ recommended.yaml
由于默认的镜像仓库网络访问不通，故改成阿里镜像
外网访问
]# sed -i ‘/targetPort: 8443/a\ \ \ \ \ \ nodePort: 30001\n\ \ type: NodePort‘ recommended.yaml
配置NodePort，外部通过https://NodeIp:NodePort 访问Dashboard，此时端口为30001
新增管理员帐号
]# cat >> recommended.yaml << EOF --- # ------------------- dashboard-admin ------------------- # apiVersion: v1 kind: ServiceAccount metadata: name: dashboard-admin namespace: kubernetes-dashboard --- apiVersion: rbac.authorization.k8s.io/v1beta1 kind: ClusterRoleBinding metadata: name: dashboard-admin subjects: - kind: ServiceAccount name: dashboard-admin namespace: kubernetes-dashboard roleRef: apiGroup: rbac.authorization.k8s.io kind: ClusterRole name: cluster-admin
创建超级管理员的账号用于登录Dashboard
5.2.2部署访问
部署Dashboard
]# kubectl apply -f recommended.yaml
状态查看
]# kubectl get all -n kubernetes-dashboard
令牌查看
创建service account并绑定默认cluster-admin管理员集群角色：
]# kubectl describe secrets -n kubernetes-dashboard $(kubectl -n kubernetes-dashboard get secret | awk ‘/dashboard-admin/{print $1}‘)使用输出的token登录Dashboard，使用火狐浏览。
相关推荐
云中舞步 2020-11-12
杨德龙 2020-11-11
JohnYork 2020-10-16
wangzhaotongalex 2020-09-22
xiaoseyihe 2020-11-16
不要皱眉 2020-10-14
Crazyshark 2020-11-13
K先生 2020-11-10
momode 2020-09-11
思君夜未眠 2020-09-04
点滴技术生活 2020-08-21
MaggieRose 2020-08-19
kevinweijc 2020-08-18
wintershii 2020-08-17
vapaad 2020-08-17
wera00 2020-08-17
移动开发与培训 2020-08-16
ReunionIsland 2020-08-16
JimyFengqi 2020-08-16